01Our Role02Products
Double-Sided Bonding TapesAcrylic Foam Structural TapesThermal Interface MaterialsEMI / RFI ShieldingInsulation & High-Temperature FilmsDouble-Sided & Foam TapesSurface Protection & MaskingOptical & Display MaterialsSpecialty & Difficult Substrates3M Industrial & Specialty Tapestesa Adhesive TapesRogers BISCO & PORON Foams
03Die-Cutting
Rotary Die-CuttingFlatbed / Steel-RuleLaser Die-CuttingCNC Digital KnifeMulti-Layer Composite
04Converting
Precision SlittingRewinding & RespoolingLamination & CompositingSheeting & Cut-to-LengthLogo, Print & Private Label
05Industries
Consumer ElectronicsNew Energy & EV BatteryAutomotive Interior & ExteriorHome AppliancesDisplay & OpticalMedical & WearablesIndustrial & MachineryRenewable EnergySignage, Print & GraphicsRail & Transport
06Strength
Testing LaboratoryCertifications
07Our Story
MilestonesOur Principles
08FAQ
Ordering & MOQQuality & Testing
09Contact
Request a QuoteFind a Representative
Get a Quote

3M 5909 VHB Acrylic Foam Tape

3M 5909 VHB Acrylic Foam Tape — supplied to your specified 3M part number and converted into pads, strips and custom shapes. Each lot is traceable and conversion-ready on our qualified lines.

  • VHB Acrylic Foam Tape
  • Supplied to 3M part No. 5909
  • Die-cut, slit or laminated to drawing
  • Lot-traceable, QC matched to spec
5909ACRYLIC FOAM TAPEDINGGU schematic illustration
Original DINGGU schematic illustration of a VHB acrylic foam tape — representative of the construction, not manufacturer photography.

At a glance

Brand
3M
Grade
5909
Family
VHB acrylic foam tape
Nominal build
0.25 – 2.3 mm
Our role
Supply & precision conversion
Request a quote for 3M 5909

Product overview

3M 5909 is a double-sided viscoelastic acrylic foam tape used as a structural joining method. The closed-cell core carries load across the whole bond line instead of concentrating it at discrete fastener points, so it distributes stress, absorbs differential thermal movement between dissimilar substrates and seals the joint at the same time.

DINGGU Tape supplies this grade as original manufacturer material and converts it on our own slitting, die-cutting and lamination lines. You can order it in roll form, or as finished parts made to your drawing — pads, strips, gaskets and multi-layer builds — with lot-level traceability on every delivery.

Construction and materials

Release linerAcrylic adhesive skinViscoelastic acrylic foam coreAcrylic adhesive skin0.25 – 2.3 mmCONSTRUCTION — 5909Layer order shown to scale of nominal build. Original DINGGU schematic — not a manufacturer drawing.
Layer sequence of the VHB acrylic foam tape construction. Drawn by DINGGU Tape for engineering orientation.

Technical data

The values below are typical reference ranges for the VHB acrylic foam tape family, provided to help you shortlist a construction. They are not reproduced from a manufacturer datasheet and are not a specification. Before release to production, confirm the figures for 3M 5909 against the current technical datasheet issued by 3M.

3M 5909 — typical family reference data
ConstructionClosed-cell viscoelastic acrylic foam, adhesive on both faces
Adhesive systemPressure-sensitive acrylic (multi-purpose and high-strength classes)
CarrierAcrylic foam core — no film carrier
Colour familyGrey · white · black · clear (grade-dependent)
Thickness range0.25 – 2.3 mm across the family
Service temperature−35 °C … +90 °C continuous (typical)
Short-term peakup to +150 °C (typical)
Substrate suitabilityPowder-coated and painted metal, aluminium, stainless steel, glass, ABS/PC, composites
Strength build-upapprox. 72 h at +23 °C to reach design strength
Low-surface-energy plasticsPrimer or flame/plasma pre-treatment advised on PP, PE and TPO

Typical applications

  • Structural glazing and panel bonding replacing rivets or spot welds
  • Metal frame-to-skin bonding on lifts, façades and equipment enclosures
  • Trim, badge and rail mounting on painted or powder-coated steel
  • Stiffener bonding where a flush, fastener-free exterior is required
  • Vibration-damping joints between dissimilar metals

Application guidance

  • Clean both faces with 50:50 isopropyl alcohol / water and allow to flash off completely
  • Apply between +21 °C and +38 °C — below +10 °C the foam will not wet out
  • Apply firm roller pressure across the full bond line to achieve intimate contact
  • Handling strength develops within about 20 min; design strength after roughly 72 h
  • Design the joint in shear where possible and avoid peel-loaded edges

Supply and conversion

How we supply 3M 5909
Supplied asOriginal manufacturer material, converted to your drawing or sample
Conversion formatsLogs, slit rolls, die-cut pads and strips, kiss-cut sheets, tabbed and finger-lift parts
Processes in housePrecision slitting, rotary and flatbed die-cutting, laser cutting, lamination
Dimensional toleranceTypically ±0.15 mm on die-cut parts and ±0.5 mm on slit width, part-dependent
Multi-layer buildsLaminated stacks combining foam, film, liner and secondary adhesives
Liner engineeringSplit liners, extended tabs, kiss-cut liners and custom release weights
Lot controlLot-level traceability from incoming reel to finished part
InspectionFirst-article inspection and dimensional report available on request
Minimum orderSample and pilot quantities accepted for qualification builds
DocumentationManufacturer datasheet and, where issued, RoHS / REACH statements forwarded with delivery

Important notice

Trademarks. 3M™ and VHB™ are trademarks of 3M Company. DINGGU Tape is an independent converter and supply partner. We are not affiliated with, authorised, sponsored or endorsed by this manufacturer, and grade references are used solely to identify the material a customer has specified.

Illustrations. All drawings on this page are original schematic artwork produced by DINGGU Tape to show a generic construction. They are not manufacturer photography, not to scale, and do not depict the exact appearance of the finished product.

Technical values. Figures are indicative family-level ranges for orientation only and carry no warranty. The manufacturer’s current datasheet is the sole authority for 3M 5909. Suitability for a specific application must be validated by the user under real service conditions.