01Our Role02Products
Double-Sided Bonding TapesAcrylic Foam Structural TapesThermal Interface MaterialsEMI / RFI ShieldingInsulation & High-Temperature FilmsDouble-Sided & Foam TapesSurface Protection & MaskingOptical & Display MaterialsSpecialty & Difficult Substrates3M Industrial & Specialty Tapestesa Adhesive TapesRogers BISCO & PORON Foams
03Die-Cutting
Rotary Die-CuttingFlatbed / Steel-RuleLaser Die-CuttingCNC Digital KnifeMulti-Layer Composite
04Converting
Precision SlittingRewinding & RespoolingLamination & CompositingSheeting & Cut-to-LengthLogo, Print & Private Label
05Industries
Consumer ElectronicsNew Energy & EV BatteryAutomotive Interior & ExteriorHome AppliancesDisplay & OpticalMedical & WearablesIndustrial & MachineryRenewable EnergySignage, Print & GraphicsRail & Transport
06Strength
Testing LaboratoryCertifications
07Our Story
MilestonesOur Principles
08FAQ
Ordering & MOQQuality & Testing
09Contact
Request a QuoteFind a Representative
Get a Quote

Rogers VFT PORON Specialty Foam

Rogers VFT PORON Specialty Foam — supplied to your specified Rogers grade and converted into pads, strips and custom shapes. Each lot is traceable and conversion-ready on our qualified lines.

  • PORON Specialty Foam
  • Supplied to Rogers grade VFT
  • Die-cut, slit or laminated to drawing
  • Lot-traceable, QC matched to spec
tVFTFOAM SHEET / BUNDINGGU schematic illustration
Original DINGGU schematic illustration of a PORON specialty and ultra-thin foam — representative of the construction, not manufacturer photography.

At a glance

Brand
Rogers
Grade
VFT
Family
PORON specialty and ultra-thin foam
Nominal build
0.15 – 3.2 mm
Our role
Supply & precision conversion
Request a quote for Rogers VFT

Product overview

Rogers VFT belongs to the PORON specialty range — formulations tuned for a specific engineering problem rather than for general gasketing. Depending on the grade that can mean an ultra-thin calliper for slim devices, a flame-rated build, improved water resistance, or a formulation that holds its properties in long-term dynamic compression.

DINGGU Tape supplies this grade as original manufacturer material and converts it on our own slitting, die-cutting and lamination lines. You can order it in roll form, or as finished parts made to your drawing — pads, strips, gaskets and multi-layer builds — with lot-level traceability on every delivery.

Construction and materials

Calendered skinMicrocellular urethane — specialty formulationPSA layerRelease liner0.15 – 3.2 mmCONSTRUCTION — VFTLayer order shown to scale of nominal build. Original DINGGU schematic — not a manufacturer drawing.
Layer sequence of the PORON specialty and ultra-thin foam construction. Drawn by DINGGU Tape for engineering orientation.

Technical data

The values below are typical reference ranges for the PORON specialty and ultra-thin foam family, provided to help you shortlist a construction. They are not reproduced from a manufacturer datasheet and are not a specification. Before release to production, confirm the figures for Rogers VFT against the current technical datasheet issued by Rogers.

Rogers VFT — typical family reference data
MaterialMicrocellular polyurethane — specialty and ultra-thin formulations
Family focusThin calliper, flame rating, moisture resistance or dynamic durability by grade
Cell structureFine open cell, non-fibrous, low outgassing
Thickness range0.15 – 3.2 mm across the family
Service temperature−40 °C … +90 °C continuous (typical)
Compression setVery low — long-term recovery is the defining property
FlammabilityFlame-rated grades available within the range
Adhesive optionCommonly supplied PSA-laminated for automated placement
Converting noteThin grades need careful kiss-cutting to stay in register
Selection driverChoose by the specific constraint — height, flame, moisture or fatigue

Typical applications

  • Ultra-thin cushioning in slim consumer devices
  • Flame-rated gasketing in electrical enclosures
  • Water-resistant seals in outdoor and wearable products
  • Dynamic compression pads that must survive long cycle counts
  • Precision shims and spacers with low closure force

Application guidance

  • Confirm the constraint you are designing to before selecting a grade
  • On very thin grades, specify a kiss-cut liner to keep small parts located
  • Keep compression within the recommended range to protect recovery
  • Verify flame rating requirements against the finished assembly, not the foam alone
  • Allow for liner and PSA calliper in tight stack-ups

Supply and conversion

How we supply Rogers VFT
Supplied asOriginal manufacturer material, converted to your drawing or sample
Conversion formatsSheets, slit rolls, die-cut gaskets and frames, kiss-cut parts, PSA-laminated stock
Processes in housePrecision slitting, rotary and flatbed die-cutting, laser cutting, lamination
Dimensional toleranceTypically ±0.15 mm on die-cut parts and ±0.5 mm on slit width, part-dependent
Multi-layer buildsLaminated stacks combining foam, film, liner and secondary adhesives
Liner engineeringSplit liners, extended tabs, kiss-cut liners and custom release weights
Lot controlLot-level traceability from incoming reel to finished part
InspectionFirst-article inspection and dimensional report available on request
Minimum orderSample and pilot quantities accepted for qualification builds
DocumentationManufacturer datasheet and, where issued, RoHS / REACH statements forwarded with delivery

Important notice

Trademarks. PORON®, BISCO® and R/bak® are trademarks of Rogers Corporation. DINGGU Tape is an independent converter and supply partner. We are not affiliated with, authorised, sponsored or endorsed by this manufacturer, and grade references are used solely to identify the material a customer has specified.

Illustrations. All drawings on this page are original schematic artwork produced by DINGGU Tape to show a generic construction. They are not manufacturer photography, not to scale, and do not depict the exact appearance of the finished product.

Technical values. Figures are indicative family-level ranges for orientation only and carry no warranty. The manufacturer’s current datasheet is the sole authority for Rogers VFT. Suitability for a specific application must be validated by the user under real service conditions.