tesa 58475
tesa 58475 — supplied to your specified tesa part number and converted into pads, strips and custom shapes. Each lot is traceable and conversion-ready on our qualified lines.
- HAF Heat-Activated Film
- Supplied to tesa part No. 58475
- Die-cut, slit or laminated to drawing
- Lot-traceable, QC matched to spec
At a glance
- Brand
- tesa
- Grade
- 58475
- Family
- HAF heat-activated adhesive film
- Nominal build
- 0.06 – 0.20 mm
- Our role
- Supply & precision conversion
Product overview
tesa 58475 is a heat-activated adhesive film (HAF). It is dry and tack-free at room temperature and only bonds when heat, pressure and dwell time are applied together, at which point the adhesive cross-links into a rigid, high-strength joint. That makes it well suited to bonding metal to plastic in thin, highly loaded assemblies where a pressure-sensitive adhesive would creep.
DINGGU Tape supplies this grade as original manufacturer material and converts it on our own slitting, die-cutting and lamination lines. You can order it in roll form, or as finished parts made to your drawing — pads, strips, gaskets and multi-layer builds — with lot-level traceability on every delivery.
Construction and materials
Technical data
The values below are typical reference ranges for the HAF heat-activated adhesive film family, provided to help you shortlist a construction. They are not reproduced from a manufacturer datasheet and are not a specification. Before release to production, confirm the figures for tesa 58475 against the current technical datasheet issued by tesa.
| Construction | Reactive adhesive film, usually supplied between release liners |
|---|---|
| Adhesive system | Heat-activated thermoset (phenolic / nitrile class) |
| Tack at room temperature | None — film is dry and repositionable before activation |
| Activation window | approx. +130 °C … +180 °C under pressure (typical) |
| Process requirement | Heat + pressure + dwell, then cool under pressure |
| Thickness range | 0.06 – 0.20 mm across the family |
| Service temperature | High — bond is thermoset once cured, resists creep |
| Substrate suitability | Metal to plastic, metal to metal, textile to metal, coated surfaces |
| Chemical resistance | Good resistance to moisture, oils and many solvents after cure |
| Converting note | Die-cut to net shape before assembly — no adhesive squeeze-out |
Typical applications
- Metal insert and stiffener bonding inside consumer electronics
- Nameplate and trim bonding where no adhesive line may be visible
- Speaker, camera bracket and shielding can attachment
- Textile-to-metal and textile-to-plastic laminating
- Thin, highly loaded joints that must not creep under sustained load
Application guidance
- Die-cut the film to net shape, then place it dry into the assembly
- Use a heated press or hot-bar with controlled temperature, force and dwell
- Hold pressure while the joint cools — releasing hot can weaken the bond
- Validate the process window on your actual parts before production
- Keep the film in its liner and store cool to protect shelf life
Supply and conversion
| Supplied as | Original manufacturer material, converted to your drawing or sample |
|---|---|
| Conversion formats | Logs, slit rolls, die-cut pads and strips, kiss-cut sheets, tabbed and finger-lift parts |
| Processes in house | Precision slitting, rotary and flatbed die-cutting, laser cutting, lamination |
| Dimensional tolerance | Typically ±0.15 mm on die-cut parts and ±0.5 mm on slit width, part-dependent |
| Multi-layer builds | Laminated stacks combining foam, film, liner and secondary adhesives |
| Liner engineering | Split liners, extended tabs, kiss-cut liners and custom release weights |
| Lot control | Lot-level traceability from incoming reel to finished part |
| Inspection | First-article inspection and dimensional report available on request |
| Minimum order | Sample and pilot quantities accepted for qualification builds |
| Documentation | Manufacturer datasheet and, where issued, RoHS / REACH statements forwarded with delivery |
Important notice
Trademarks. tesa®, ACXplus®, Softprint® and HAF® are trademarks of tesa SE. DINGGU Tape is an independent converter and supply partner. We are not affiliated with, authorised, sponsored or endorsed by this manufacturer, and grade references are used solely to identify the material a customer has specified.
Illustrations. All drawings on this page are original schematic artwork produced by DINGGU Tape to show a generic construction. They are not manufacturer photography, not to scale, and do not depict the exact appearance of the finished product.
Technical values. Figures are indicative family-level ranges for orientation only and carry no warranty. The manufacturer’s current datasheet is the sole authority for tesa 58475. Suitability for a specific application must be validated by the user under real service conditions.