01Our Role02Products
Double-Sided Bonding TapesAcrylic Foam Structural TapesThermal Interface MaterialsEMI / RFI ShieldingInsulation & High-Temperature FilmsDouble-Sided & Foam TapesSurface Protection & MaskingOptical & Display MaterialsSpecialty & Difficult Substrates3M Industrial & Specialty Tapestesa Adhesive TapesRogers BISCO & PORON Foams
03Die-Cutting
Rotary Die-CuttingFlatbed / Steel-RuleLaser Die-CuttingCNC Digital KnifeMulti-Layer Composite
04Converting
Precision SlittingRewinding & RespoolingLamination & CompositingSheeting & Cut-to-LengthLogo, Print & Private Label
05Industries
Consumer ElectronicsNew Energy & EV BatteryAutomotive Interior & ExteriorHome AppliancesDisplay & OpticalMedical & WearablesIndustrial & MachineryRenewable EnergySignage, Print & GraphicsRail & Transport
06Strength
Testing LaboratoryCertifications
07Our Story
MilestonesOur Principles
08FAQ
Ordering & MOQQuality & Testing
09Contact
Request a QuoteFind a Representative
Get a Quote

Rogers 4790-92-20 PORON Urethane Foam

Rogers 4790-92-20 PORON Urethane Foam — supplied to your specified Rogers grade and converted into pads, strips and custom shapes. Each lot is traceable and conversion-ready on our qualified lines.

  • PORON Urethane Foam
  • Supplied to Rogers grade 4790-92-20
  • Die-cut, slit or laminated to drawing
  • Lot-traceable, QC matched to spec
t4790-92-20FOAM SHEET / BUNDINGGU schematic illustration
Original DINGGU schematic illustration of a PORON industrial polyurethane foam — representative of the construction, not manufacturer photography.

At a glance

Brand
Rogers
Grade
4790-92-20
Family
PORON industrial polyurethane foam
Nominal build
0.25 – 12.7 mm
Our role
Supply & precision conversion
Request a quote for Rogers 4790-92-20

Product overview

Rogers 4790-92-20 is an open-cell microcellular polyurethane foam used where a gasket must stay resilient for the life of the product. Unlike conventional blown foams it recovers almost fully after long-term compression, so a seal made from it keeps pushing back against the mating face instead of taking a permanent set and leaking.

DINGGU Tape supplies this grade as original manufacturer material and converts it on our own slitting, die-cutting and lamination lines. You can order it in roll form, or as finished parts made to your drawing — pads, strips, gaskets and multi-layer builds — with lot-level traceability on every delivery.

Construction and materials

Calendered skinOpen-cell microcellular urethaneOptional PSA layerOptional release liner0.25 – 12.7 mmCONSTRUCTION — 4790-92-20Layer order shown to scale of nominal build. Original DINGGU schematic — not a manufacturer drawing.
Layer sequence of the PORON industrial polyurethane foam construction. Drawn by DINGGU Tape for engineering orientation.

Technical data

The values below are typical reference ranges for the PORON industrial polyurethane foam family, provided to help you shortlist a construction. They are not reproduced from a manufacturer datasheet and are not a specification. Before release to production, confirm the figures for Rogers 4790-92-20 against the current technical datasheet issued by Rogers.

Rogers 4790-92-20 — typical family reference data
MaterialOpen-cell microcellular polyurethane foam
Cell structureFine, uniform open cell — non-fibrous
Grade codingNumeric suffix denotes the density / compression-force-deflection class in the series
Density rangeapprox. 240 – 640 kg/m³ across the family (typical)
Compression setVery low — recovers after prolonged compression
Service temperature−40 °C … +90 °C continuous (typical)
Thickness range0.25 – 12.7 mm across the family
FlammabilityUL 94 rated grades available within the range (e.g. V-0 class)
Adhesive optionAvailable plain or PSA-laminated one or both sides
Sealing behaviourSeals at low closure force — suited to thin plastic housings

Typical applications

  • Enclosure and housing gasketing at low closure force
  • Display and lens cushioning in consumer electronics
  • Battery-pack cell cushioning and swell management
  • NVH pads and squeak/rattle isolation in vehicle interiors
  • Compression seals around switches, buttons and connectors

Application guidance

  • Design for a target compression of roughly 25–50 % for a reliable seal
  • Avoid over-compression — it raises closure force without improving sealing
  • Allow for the PSA thickness in the stack-up when calculating gap
  • Specify skin or skinless faces depending on whether wicking matters
  • Die-cut gaskets rather than splicing strips where a continuous seal is required

Supply and conversion

How we supply Rogers 4790-92-20
Supplied asOriginal manufacturer material, converted to your drawing or sample
Conversion formatsSheets, slit rolls, die-cut gaskets and frames, kiss-cut parts, PSA-laminated stock
Processes in housePrecision slitting, rotary and flatbed die-cutting, laser cutting, lamination
Dimensional toleranceTypically ±0.15 mm on die-cut parts and ±0.5 mm on slit width, part-dependent
Multi-layer buildsLaminated stacks combining foam, film, liner and secondary adhesives
Liner engineeringSplit liners, extended tabs, kiss-cut liners and custom release weights
Lot controlLot-level traceability from incoming reel to finished part
InspectionFirst-article inspection and dimensional report available on request
Minimum orderSample and pilot quantities accepted for qualification builds
DocumentationManufacturer datasheet and, where issued, RoHS / REACH statements forwarded with delivery

Important notice

Trademarks. PORON®, BISCO® and R/bak® are trademarks of Rogers Corporation. DINGGU Tape is an independent converter and supply partner. We are not affiliated with, authorised, sponsored or endorsed by this manufacturer, and grade references are used solely to identify the material a customer has specified.

Illustrations. All drawings on this page are original schematic artwork produced by DINGGU Tape to show a generic construction. They are not manufacturer photography, not to scale, and do not depict the exact appearance of the finished product.

Technical values. Figures are indicative family-level ranges for orientation only and carry no warranty. The manufacturer’s current datasheet is the sole authority for Rogers 4790-92-20. Suitability for a specific application must be validated by the user under real service conditions.