01Our Role02Products
Double-Sided Bonding TapesAcrylic Foam Structural TapesThermal Interface MaterialsEMI / RFI ShieldingInsulation & High-Temperature FilmsDouble-Sided & Foam TapesSurface Protection & MaskingOptical & Display MaterialsSpecialty & Difficult Substrates3M Industrial & Specialty Tapestesa Adhesive TapesRogers BISCO & PORON Foams
03Die-Cutting
Rotary Die-CuttingFlatbed / Steel-RuleLaser Die-CuttingCNC Digital KnifeMulti-Layer Composite
04Converting
Precision SlittingRewinding & RespoolingLamination & CompositingSheeting & Cut-to-LengthLogo, Print & Private Label
05Industries
Consumer ElectronicsNew Energy & EV BatteryAutomotive Interior & ExteriorHome AppliancesDisplay & OpticalMedical & WearablesIndustrial & MachineryRenewable EnergySignage, Print & GraphicsRail & Transport
06Strength
Testing LaboratoryCertifications
07Our Story
MilestonesOur Principles
08FAQ
Ordering & MOQQuality & Testing
09Contact
Request a QuoteFind a Representative
Get a Quote

tesa 73422

tesa 73422 — supplied to your specified tesa part number and converted into pads, strips and custom shapes. Each lot is traceable and conversion-ready on our qualified lines.

  • Softprint Double-Sided Tape
  • Supplied to tesa part No. 73422
  • Die-cut, slit or laminated to drawing
  • Lot-traceable, QC matched to spec
73422PLATE MOUNTING FOAMDINGGU schematic illustration
Original DINGGU schematic illustration of a Softprint plate-mounting tape — representative of the construction, not manufacturer photography.

At a glance

Brand
tesa
Grade
73422
Family
Softprint plate-mounting tape
Nominal build
0.38 – 1.90 mm
Our role
Supply & precision conversion
Request a quote for tesa 73422

Product overview

tesa 73422 is a compressible double-sided foam tape for mounting flexographic printing plates. The foam layer acts as a controlled cushion between plate and cylinder: it absorbs impression pressure, prevents the plate from bouncing at the print nip and so reduces dot gain, halo and bar marking while extending plate life.

DINGGU Tape supplies this grade as original manufacturer material and converts it on our own slitting, die-cutting and lamination lines. You can order it in roll form, or as finished parts made to your drawing — pads, strips, gaskets and multi-layer builds — with lot-level traceability on every delivery.

Construction and materials

Release linerPlate-side adhesiveCompressible polyethylene foamCylinder-side adhesive0.38 – 1.90 mmCONSTRUCTION — 73422Layer order shown to scale of nominal build. Original DINGGU schematic — not a manufacturer drawing.
Layer sequence of the Softprint plate-mounting tape construction. Drawn by DINGGU Tape for engineering orientation.

Technical data

The values below are typical reference ranges for the Softprint plate-mounting tape family, provided to help you shortlist a construction. They are not reproduced from a manufacturer datasheet and are not a specification. Before release to production, confirm the figures for tesa 73422 against the current technical datasheet issued by tesa.

tesa 73422 — typical family reference data
ConstructionCompressible PE foam carrier, adhesive on both faces
Adhesive systemDifferential — plate side and cylinder side tuned separately
CarrierClosed-cell polyethylene foam cushion
Hardness classesSoft / medium / hard cushion depending on grade
Thickness range0.38 – 1.90 mm across the family
Service temperature+5 °C … +40 °C press-room conditions (typical)
Print benefitReduced dot gain, cleaner solids, less bar marking
RemovabilityDesigned for clean plate demounting without foam split
Substrate suitabilityPhotopolymer plates, steel and aluminium print cylinders, sleeves
Selection driverChoose cushion hardness by artwork type — line, solid or combination

Typical applications

  • Flexographic plate mounting on cylinders and sleeves
  • Narrow-web label printing where dot fidelity is critical
  • Corrugated post-print with heavy solid coverage
  • Flexible packaging print with fine highlight dots
  • Repeat-job plate remounting where clean demount matters

Application guidance

  • Mount onto a clean, degreased cylinder or sleeve surface
  • Avoid stretching the tape during application — lay it down relaxed
  • Butt joints rather than overlap them to prevent a raised print line
  • Use a mounting machine or roller to expel air along the whole width
  • Select softer cushions for solids and harder cushions for fine line work

Supply and conversion

How we supply tesa 73422
Supplied asOriginal manufacturer material, converted to your drawing or sample
Conversion formatsLogs, slit rolls, die-cut pads and strips, kiss-cut sheets, tabbed and finger-lift parts
Processes in housePrecision slitting, rotary and flatbed die-cutting, laser cutting, lamination
Dimensional toleranceTypically ±0.15 mm on die-cut parts and ±0.5 mm on slit width, part-dependent
Multi-layer buildsLaminated stacks combining foam, film, liner and secondary adhesives
Liner engineeringSplit liners, extended tabs, kiss-cut liners and custom release weights
Lot controlLot-level traceability from incoming reel to finished part
InspectionFirst-article inspection and dimensional report available on request
Minimum orderSample and pilot quantities accepted for qualification builds
DocumentationManufacturer datasheet and, where issued, RoHS / REACH statements forwarded with delivery

Important notice

Trademarks. tesa®, ACXplus®, Softprint® and HAF® are trademarks of tesa SE. DINGGU Tape is an independent converter and supply partner. We are not affiliated with, authorised, sponsored or endorsed by this manufacturer, and grade references are used solely to identify the material a customer has specified.

Illustrations. All drawings on this page are original schematic artwork produced by DINGGU Tape to show a generic construction. They are not manufacturer photography, not to scale, and do not depict the exact appearance of the finished product.

Technical values. Figures are indicative family-level ranges for orientation only and carry no warranty. The manufacturer’s current datasheet is the sole authority for tesa 73422. Suitability for a specific application must be validated by the user under real service conditions.